Grades 200 and 201 nickel are normally preferred for handling concentrated, high temperature caustic. However, when sulfur compounds are present as well, or for ammonium hydroxide service, 600 alloy is suggested. 600 alloy is subject to stress corrosion cracking in hot, concentrated caustic alkalies.
Alloy 600 - Nickel Alloys from NeoNickelThis alloy has excellent oxidation resistance up to 1093°C combined with high carburisation resistance and demonstrates good performance in high temperature nitriding environments. It is not recommended that Inconel® Alloy 600 be used at red heat temperatures where sulphur is present.
Alloy 602 CA is a high-carbon nickel-chromium-iron alloy with additions of the micro-alloying elements titanium and zirconium together with aluminum and yttrium. It is normally supplied in the solution-annealed condition with an oxidized or descaled surface.
Alloy 800/800H Heat Resistant Nickel - Sandmeyer Steel
General PropertiesCreep and Rupture PropertiesOxidation ResistanceCorrosion ResistanceAlloys 800H (UNS N08810) and 800HT (UNS N08811) are dual-certifiable Nickel-Iron-Chromium materials that resist oxidation, carburization and other high temperature corrosion. The chemical composition of the two alloys are identical to Alloy 800 (UNS N08800), with the exception of the higher level of carbon present in both grades (0.050.10%) in alloy 800H, and (0.060.10%) in alloy 800HT. Alloy 800HT also has an addition of up 1.0 % aluminum and titanium. In addition to the chemistry restri600 - Rolled Alloys, Inc.Grades 200 and 201 nickel are normally preferred for handling concentrated, high temperature caustic. However, when sulfur compounds are present as well, or for ammonium hydroxide service, 600 alloy is suggested. 600 alloy is subject to stress corrosion cracking in hot, concentrated caustic alkalies.
Comparing materials for high-temperature steam pipingThe U.S. had been trying to develop a new material since the middle 1970s to bridge the gap between ferritic P22 and austenitic steels with respect to creep rupture strength for high-temperature service from 540 to 600 degrees C. Development of any new material, especially for high-temperature service, requires many years, because creep rupture strengths are established based on longtime
The DP steel exhibits higher initial work hardening rate, higher ultimate tensile strength, and higher TS/YS ratio than a similar yield strength HSLA. Additional engineering and true stress-strain curves for DP steel grades are located in Figure 2-5 in the Advanced High-Strength Steels Application Guidelines.
High Temperature Alloys, NITRONIC, INCONEL, HASTELLOYHigh temperature resistance is essential in many applications. Gas turbines, fuel nozzles, heat treating fixtures, and furnace muffles. These materials must stand up to high heat, extreme oxidation potential and cycling. HASTELLOY ® alloy X (HX) (UNS N06002) Ni 47.5, Cr 21.8, Fe 18.5, Mo 9.0
High Temperature Coating Options NewtexNewtex offers over 20 standard high temperature coatings, treatments, and laminates that can be applied to most of our high temperature fabrics including our original Zetex® fiberglass fabric to meet the performance requirements of your application. Select from high temperature coatings and laminates to boost resistance to vapor, weathering, oil, water, chemical attack, abrasion wear
Price:High to Low HP . Pump HP. Pump HP (Horsepower) is the measurement of a pump motors output power. $600 (4) $600 - $700 (1) $800 - $900 (2) $900 - $1000 (1) These high-temperature submersible sump pumps transfer hot liquids such as furnace condensate or waste from boiler blowdown. They are also for use in plant washdown sump
Pumps - Texas Process EquipmentCast iron, aluminum, stainless steel, Hastelloy C, polypropylene and PVDF materials of construction. Flows to 275 GPM. Drum pump, flap valve and powder handling versions available. Air operated piston pumps in steel and stainless steel construction for pumping high viscosity materials, capable of discharge pressures to 10,000psi.
SMEX - Steel Temperature ChartThese colours may be used in determining the temperature of the steel, when for example tempering tool steel. The melting point of mild steel (0.1%~0.2% Carbon) is approximately 1500°C (2730°F), and a bit higher for the various alloy steels. The MP of these steels depends on the composition and quantity of the alloying metal.
- Economical stainless steel grade due to low alloy content. - Low thermal expansion coefficient results in reduced distortion in welding and in high temperature applications. - Good scaling resistance to over 600oC, and useful strength at these elevated temperatures can be a good choice for furnace bodies.
Strenx 900 - high-strength structural steel - SSABStrenx® 900 Strenx® 900 is a structural steel that guarantees a minimum yield strength of up to 900 MPa depending on thickness. Strenx ® 900 provides a unique combination of strength and toughness together with first-rate workshop properties. Typical applications
Thurmalox Industrial high-temperature protective coatings.Thurmalox - Industrial high-temperature protective coatings. Dampney has served the home and hearth industries for many years providing high performance heat resistant coatings to
In fact, in their Alloy Performance Guide, Rolled Alloys lists RA330 as having Better (meaning above average) performance for strength, oxidation resistance, carburization resistance, and oxidizing sulfur resistance while being rated as Best for thermal shock resistance among the high-temperature alloys they offer. Inconel 600
American Plumber WIC-600 Undersink Filter SystemThe American Plumber WIC-600 icemaker and water dispenser filter system reduces chlorine and other contaminants for cleaner and more refreshing drinking water. The WIC-600 System fits any 1/4-inch water line. The filter uses Activated Carbon Block to remove contaminants for up to 6 months.